Hello,

You must set:
	g_ssl_allow "*"
	g_ssl_allow_imap "*"
on both machines to enable ssl.

Regards,
Stuart

On 17/02/2011 8:37 p.m., plear wrote:
>
> Thanks Lyle,
>
> I opened Port 110 on both ends. Now I get the following:
>
>
>
> (I'm trying to mirror two machines over the internet.) SSL is NOT
> disabled on either machine. Port 110 is open in both directions.
>
>
> Mirror Status (MASTER) to (<SLAVE IP>) live
> Add: 61 (0.0/s) live=0
> Sent: 67 (0.0/s)
> Queue: 0k 0.0%
> Config: Feb 16 15:24:53
> Resync: Total=22151 0.0, Resent=9840, Prune=0, Dirs=286 Th=5
> State: OpenList2-NULL
> Que: Done que 2 in 4 sec
> LastErr: -ERR SSL Not allowed for ip (<MASTER IP>)
> In: add=0 del=0 rename=0 fail=0 prune=0
>
>
> Mirror Status (SLAVE) to (<MASTER IP>) live
> Add: 2 (0.0/s) live=0
> Sent: 0 (0.0/s)
> Queue: 0k 0.0%
> Config: Feb 17 00:25:41
> Resync: No record of last resync command
> State: Started 1
> Que:
> Info: 08:22 Open (<MASTER IP>) failed Operation now in progress 33 sec
> In: add=9379 del=136 rename=45 fail=13 prune=0
>
>
> Thank you.
>
> Patrick
>
>
>
>
>
> On Feb 9, 2011, at 7:23 PM, Lyle Giese wrote:
>
>> plear wrote:
>>> Hi,
>>>
>>> Mirroring won't start. I get an "open connection refused" on the
>>> master. Here is the detail:
>>>
>>>
>>> I have set up both the master and slave per
>>> http://netwinsite.com/surgemail/help/mirror.htm and started the
>>> mirror (on the master only) as follows:
>>>
>>> issue "tellmail resync_config" on master (if using g_mirror_config)
>>> issue "tellmail surgehost_update" on master
>>> issue "tellmail resync_nwauth"' on master (if using nwauth)
>>> issue "tellmail resync_fast" on master
>>>
>>> When I issue the "tellmail status" command I get the following on the
>>> MASTER
>>>
>>> ----------------------------------------------------------------------------
>>> Mirror Status (MASTER) to (XXX.XXX.XXX.XXX [IP of slave]) live
>>> Add: 7 (0.0/s) live=0
>>> Sent: 0 (0.0/s)
>>> Queue: 1395k 0.0%
>>> Config: Feb 09 16:52:53
>>> Open failed
>>> State: Started 1
>>> Que:
>>> Info: 16:53 readline open Connection refused after 0 seconds
>>> In: add=0 del=0 rename=0 fail=0 prune=0
>>> ----------------------------------------------------------------------------
>>>
>>> Almost an hour after the above commands were given to the master, the
>>> SLAVE shows this:
>>>
>>> ----------------------------------------------------------------------------
>>> Mirror Status (SLAVE) to (XX.XX.XX.XX [IP of MASTER) live
>>> Add: 0 (0.0/s) live=0
>>> Sent: 0 (0.0/s)
>>> Queue: 0k 0.0%
>>> Config: Not since restart
>>> Resync: No record of last resync command
>>> State: Started 1
>>> Que:
>>> Info: 02:27 Open (XX.XX.XX.XX [IP of MASTER]) failed Operation now in
>>> progress 33 sec
>>> In: add=0 del=0 rename=0 fail=0 prune=0
>>> ----------------------------------------------------------------------------
>>>
>>>
>>> Every time I repeat this, the time under "Info: " changes to the
>>> current time for both the Master and Slave. Please disregard the wide
>>> discrepancy in times - the machines are set to different time zones.
>>>
>>> Any ideas as to why it is not starting?
>>>
>>> Thank you.
>>>
>>> Patrick
>>>
>>>
>>>
>>>
>> I believe that mirroring is done over tcp port 110. Could you have
>> firewall issues preventing them from talking on port 110? Can you telnet
>> to port 110 from the master to slave or vis-versa?
>>
>> Lyle Giese
>> LCR Computer Services, Inc.
>>
>>
>
>
> ------------------------------------------------------------------------------------------
> The problem with socialism is that you eventually run out of other
> people's money.
>
>
>
>